How the construction holds
Once set, the material wedges itself between the surrounding teeth. No adhesive, no chemicals – purely mechanical retention. The bridge on the inside, the crown on the outside.
As with the upper teeth, gravity helps here. Bend 10–20°.
Gravity helps – the structure rests on the lower arch.
If you are missing three teeth, we recommend the Denticor 3 pack.
Difficulty
5/10 – moderately difficult
Time
25–30 mins
Material
DentiFlex, 5.5 g (most of the bottle)
Retention
Interlocking (form-fit lock)
Row of teeth
Lower, front region
Once set, the material wedges itself between the surrounding teeth. No adhesive, no chemicals – purely mechanical retention. The bridge on the inside, the crown on the outside.
The structure consists of a composite crown and a bridge made from DentiFlex material. The bridge is concealed from the inside (towards the tongue) – from the outside, you can only see the new tooth.
Three adjacent teeth in the lower anterior-lateral region already require a longer and more secure bridge. The crowns must fit into the space in such a way that there is room on either side for the stabilising DentiFlex, which is pressed against the surrounding teeth once in place.
Examine the gap – three teeth in the corner
Open your mouth. Three teeth are missing – from the midline across the corner of the arch. On the left is the opposite central incisor (thin, left anchor), on the right is a premolar (thick, main anchor). The gap has a slight curve – approximately 10–20° – where the frontal plane transitions to the lateral plane.
Prepare hot water (80–85°C)
Use a water thermometer to prepare water at 80–85 °C in a heat-resistant container. Do not put your fingers into the hot water. Lift softened DentiFlex out with a spoon and let it cool until comfortably warm before any contact with your mouth.
Pour out most of the DentiFlex (~5–6 g)
The three teeth in the lower arch require less material than the upper arch – the lower front teeth are smaller. Pour out approximately three-quarters of the bottle.
Soften the granules (1.5–3 minutes)
Drop the granules into hot water. In 1.5–3 minutes, they’ll change colour from white to transparent and become soft. Remove them with a spoon and shape them into a single ball. Work quickly – the material sets fast.
Create a straight bridge with three crowns
First, create a straight bridge – you’ll add the curve in the next step. Three crowns side by side from left to right: 1) Central incisor – the largest lower front tooth, flat and wide. 2) Lateral incisor – smaller than the central incisor, slightly rounded. 3) Canine – conical, pointed upwards. The bridge must be straight and all three positions must lie in the same plane.
Bend the bridge (a slight bend of 10–20°)
The direction changes between the lateral incisor and canine. Keep the central and lateral crowns aligned with the front of the arch, then shape the canine end along its natural curve. Use the confirmed side and your own tooth line as the reference; avoid a sharp or forced bend.
Insert the bridge in sequence – gravity helps
You cannot insert the entire bridge in one go because of the bend. Procedure: 1) Place the front end against the opposite central incisor – gently, as it is thin. 2) Guide the bend around the corner of the arch. 3) Place the side end against the premolar – more firmly; the premolar is the main anchor. 4) Press the whole bridge downwards. The advantage of the lower jaw: gravity holds the bridge in place – less stress during insertion.
Finish shaping the wedge – take extra care with the thinner adjacent tooth
Gently press the ends of the bridge against the adjacent teeth to create a form-fit lock. Press the left end – near the opposite central incisor – particularly gently. The central incisor in the lower arch is thinner and more fragile. You can press the right-hand end – next to the premolar – more firmly. The premolar is the main anchor and can withstand close contact.
Keep the canine crown's pointed outline visible
Check the pointed canine crown in the mirror and compare its alignment with your natural teeth. If soft DentiFlex covers its visible outline, remove the excess or adjust the support. Shape the soft DentiFlex, not the hard resin crown. If the supplied crown itself appears incorrect, contact Denticor before altering it.
Align the height of all three crowns
Check the height of all three crowns by biting down. None must interfere with the bite – three interfering teeth cause pain when eating. Rule: better slightly lower than higher.
Remove while soft; let it harden outside the mouth
After shaping, carefully remove the complete piece while the DentiFlex is still soft. Let it cool and harden completely outside the mouth. Then check that the crown stays joined to the bridge, the fit is comfortable and you can insert and remove the piece without force.
Test – four tests
1) Visually – check the height, shape and symmetry with the opposite side in front of a mirror. 2) By biting down – clench your teeth; no crown should get in the way. 3) By speaking – say A-E-I-O-U; does it stay in place? 4) With your tongue – run your tongue along the inside of the bridge; is it smooth and free of sharp edges? Done.
You can soften DentiFlex again outside the mouth and adjust it as described in the guide. Let it cool until comfortably warm before any mouth contact. Remove the piece while it is still soft and let it harden fully outside the mouth. Check the crown connection, comfortable tooth contact and easy removal again before use.
Not holding / falling out
Reason: Loose dentures.
Solution: Soften (80–85°C). Let it cool until comfortably warm before any mouth contact. Tighter contacts.
It set quickly
Reason: DentiFlex sets quickly.
Solution: Hot water (80–85°C), it will soften. Let it cool until comfortably warm before any mouth contact.
Remove the complete piece before sleep. Clean daily with lukewarm water and a soft brush. Do not boil the piece or use aggressive cleaners. Let it dry, then store it in a dry, dark place at room temperature, protected from sunlight and temperatures above 40 °C.
If you have a fresh wound, inflammation or swelling – wait until it has healed. If the surrounding teeth are loose – Denticor has nothing to grip onto. In these cases, visit your dentist first.
Your situation may be slightly different:
LOWER ANTERIOR INCISOR
Difficulty level 2/10, 10 minutes
LOWER LATERAL INCISOR
Difficulty level 2/10, 10 minutes
LOWER CANINE
Difficulty level 2/10, 15 minutes
Not sure which guide is right for you?
The AI test will determine this in 2 minutes, create a personalised guide and recommend the most suitable Denticor pack.
Take the test →Do not use Denticor if: fresh extraction wounds, gum inflammation, loose teeth. If in doubt, visit your dentist first.